Difference between revisions of "13.3 - VoidSafe™ Protection System"
m |
|||
Line 3: | Line 3: | ||
− | + | VoidSafe™ is a moulded non-slip composite Glass Reinforced Plastic (GRP) floor grating system, it is designed, supplied and installed by SMD along with the metal deck operations. | |
− | The installation of | + | The installation of VoidSafe™ eliminates the requirement for void handrail protection systems and temporary void protection during construction, providing a final void riser protection product which minimises floor obstructions during the process. |
'''Material specification''' | '''Material specification''' | ||
− | Two main components produce composite GRP: Polyester, resin and glass fibres. Isopthalic polyester resin is used to manufacture | + | Two main components produce composite GRP: Polyester, resin and glass fibres. Isopthalic polyester resin is used to manufacture VoidSafe™ mesh due to its flexibility and cost. |
Line 17: | Line 17: | ||
'''Fire resistance''' | '''Fire resistance''' | ||
− | + | *Standard Iso Resin - BS 476 Part 7 Class 2 | |
'''Typical edge detail''' | '''Typical edge detail''' | ||
− | The minimum bearing required for | + | The minimum bearing required for VoidSafe™ is 50mm. Around the void perimeter, the VoidSafe™ is supported on specially engineered trim manufactured from 2.0mm gauge material with a 40mm recess to provide the VoidSafe™ at the same level as the adjacent slab. Ref Fig 13.3a and 13.3b. |
Line 44: | Line 44: | ||
'''Service penetrations''' | '''Service penetrations''' | ||
− | Where service penetrations are required in the VoidSafe™ Protection System, additional trimming support may be required. Should voids be required, a detailed void layout must be submitted to enable any additional support | + | Where service penetrations are required in the VoidSafe™ Protection System, additional trimming support may be required. Should voids be required, a detailed void layout must be submitted to enable any additional support requirements to be specified. |
This information should be made available at design stage, to avoid the need for support to be installed retrospectively. | This information should be made available at design stage, to avoid the need for support to be installed retrospectively. |
Revision as of 17:49, 30 January 2017
Back to main Contents page
VoidSafe™ is a moulded non-slip composite Glass Reinforced Plastic (GRP) floor grating system, it is designed, supplied and installed by SMD along with the metal deck operations.
The installation of VoidSafe™ eliminates the requirement for void handrail protection systems and temporary void protection during construction, providing a final void riser protection product which minimises floor obstructions during the process.
Material specification
Two main components produce composite GRP: Polyester, resin and glass fibres. Isopthalic polyester resin is used to manufacture VoidSafe™ mesh due to its flexibility and cost.
Fire resistance
- Standard Iso Resin - BS 476 Part 7 Class 2
Typical edge detail
The minimum bearing required for VoidSafe™ is 50mm. Around the void perimeter, the VoidSafe™ is supported on specially engineered trim manufactured from 2.0mm gauge material with a 40mm recess to provide the VoidSafe™ at the same level as the adjacent slab. Ref Fig 13.3a and 13.3b.
X = 114mm minimum, this will need increasing for shallow slab depths (<150mm).
Fixings
Fixings must be in each corner, be at a minimum of 1000mm centres and there should be a minimum of 4 fixings in each sheet.
Service penetrations
Where service penetrations are required in the VoidSafe™ Protection System, additional trimming support may be required. Should voids be required, a detailed void layout must be submitted to enable any additional support requirements to be specified.
This information should be made available at design stage, to avoid the need for support to be installed retrospectively.
Other items within 13.0 - Product options:-