Oldest pages
Showing below up to 73 results in range #51 to #123.
View (previous 100 | next 100) (20 | 50 | 100 | 250 | 500)
- 13.9 - Plastisol (PF) Coating (14:54, 22 October 2019)
- 5.1 - Reinforcement (15:19, 30 October 2020)
- 8.13 - Fixing specification (09:44, 16 December 2020)
- 13.2 - Crushed ends deck sheets (10:53, 17 December 2020)
- 2.3 - Stud welding (15:26, 29 September 2021)
- 13.8 - Service fixings (14:15, 13 December 2021)
- 9.3 - Offloading, hoisting and storage (12:25, 13 January 2022)
- 8.5 - Extended end laps (13:46, 9 March 2022)
- 7.5 - Aggressive environments (16:45, 24 March 2022)
- 11.9 Void Protection (13:11, 13 April 2022)
- 11.11 Disposal of Waste (13:51, 13 April 2022)
- 4.1 Construction stage and construction deflections (10:06, 14 April 2022)
- 4.1 - Benefits of composite metal deck (11:25, 14 April 2022)
- 11.2 - Decking around columns (12:42, 14 April 2022)
- 11.7 - Scorching of beams (13:24, 14 April 2022)
- 11.7 Stud Welding causing Scorching to beam (13:41, 14 April 2022)
- 11.3 - Unpainted top flanges (14:38, 14 April 2022)
- 11.5 - Static generator or mains supply (14:55, 14 April 2022)
- 11.6 - Testing (14:56, 14 April 2022)
- 11.8 - Minimising grout loss (15:50, 14 April 2022)
- 6.9 Pre-studded beams (15:07, 19 April 2022)
- 13.7 - Off-site cutting (15:10, 19 April 2022)
- 12.10 - Surface flatness (13:43, 20 April 2022)
- 12.12 - Post-installation characteristics (14:04, 20 April 2022)
- 12.13 Surplus concrete waste (14:08, 20 April 2022)
- 12.1 - Site considerations (15:04, 20 April 2022)
- 9.1 - Delivery and access (15:17, 20 April 2022)
- 6.1 - Shear stud LAW (length after weld) (15:26, 20 April 2022)
- 7.2 - Fixing tool and stud welding gun restrictions (08:12, 21 April 2022)
- 3.2 - Documentation (08:13, 21 April 2022)
- 4.4 - Lateral restraint and diaphragm action (08:13, 21 April 2022)
- 4.8 - Edge trim (08:29, 21 April 2022)
- 12.9 - Surface finish (08:35, 21 April 2022)
- 9.4 - Pack labels / loading-out locations (10:56, 21 April 2022)
- 13.3 - VoidSafe™ Protection System (15:27, 25 April 2022)
- 14.1 - SMD documentation (11:08, 12 July 2022)
- 14.3 - Design standards (11:12, 12 July 2022)
- 14.4 - Further reading (11:12, 12 July 2022)
- 6.6 - Shear stud spacing (09:34, 18 July 2022)
- 8.18 - Forming openings (11:48, 8 August 2022)
- 9.2 - Pack size and sheet length limits (14:01, 9 November 2022)
- 4.7 - Cantilevers (15:25, 9 January 2023)
- 7.4 - Durability (12:57, 20 January 2023)
- 2.2 - Floor deck material specification (12:58, 20 January 2023)
- 2.4 - Roof deck material specification (13:00, 20 January 2023)
- 1.0 - Product certification (12:56, 31 January 2023)
- 9.5 Lifting Shear Studs to Level (14:38, 20 April 2023)
- 5.3 - Fire (13:21, 6 June 2023)
- 13.6 - TAB-Deck™ – Fibre concrete (15:09, 14 June 2023)
- 8.1 - Quality (14:52, 15 August 2023)
- 6.8 - Alternative Shear Connectors (08:55, 29 August 2023)
- 4.9 - Flashings (08:39, 26 September 2023)
- 11.10 VoidSafe® Protection System (13:11, 6 October 2023)
- 12.8 - Placement (08:50, 19 October 2023)
- 4.3 - Temporary propping (08:55, 19 October 2023)
- 0.0 - Introduction to the TGN (08:56, 19 October 2023)
- 5.2 - Saw cuts (08:57, 19 October 2023)
- 12.7 - Concrete mix requirements (08:57, 19 October 2023)
- 14.2 - Industry best practice (09:00, 19 October 2023)
- 6.7 -Transverse reinforcement for composite beams (09:01, 19 October 2023)
- 5.6 - Forming service holes (09:07, 19 October 2023)
- 11.0 - Installation - Floor deck and shear studs (15:07, 1 November 2023)
- 11.6 - Stud welding: Testing (16:00, 1 November 2023)
- 4.2 - Sheet lengths (16:20, 1 November 2023)
- Main Page (12:37, 3 November 2023)
- 4.0 Design, Floor deck (12:46, 3 November 2023)
- 2.0 - Specification (13:08, 3 November 2023)
- Contents (13:55, 3 November 2023)
- 10.1 - Safety nets (15:08, 3 November 2023)
- 5.4 - Moving concentrated loads (15:10, 3 November 2023)
- 4.5 - Bearings / Support (12:34, 25 March 2024)
- 12.6 - Reinforcement drawings and bending schedules (14:53, 17 April 2024)
- 4.6 - Fixings (11:10, 16 May 2024)
